Photo-Oxidation of MiniSOG Related to Cultured Neurons
Daniela Boassa, Mark H. Ellisman, Mason Mackey, Thomas Steinkellner, Matthew Madany, Matthias G. Haberl, Vivien Zell, Carolina Li, Junru Hu, Ranjan Ramachandra, Stephen Adams, Thomas S. Hnasko
UCSD
NCMIR
Photo-oxidation
MiniSOG
miniSOG
glutamatergic synapse
glutamate
vesicular glutamate transporter (VGLUT2)
neurotransmission
3D electron microscopy (EM)
deep learning
CDeep3M
genetic EM probe
ventral tegmental area (VTA)
synaptic vesicles
Abstract
This is a general protocol is for photo-oxidizing neuro-vesicle proteins with MiniSOG. We developed a genetically encoded probe to identify glutamatergic synaptic vesicles at the levels of both light and electron microscopy (EM) by fusing the mini singlet oxygen generator (miniSOG) probe to an intralumenal loop of the vesicular glutamate transporter-2.
Before start
SET UP FOR PHOTO-OXIDATION
1.Filters we use for miniSOG
Leica Blue Excitation : 11513878
Ex:450-490
DM 510
Em:LP 515
Semrock Lucifer Yellow Filter : LuciferYellow-B-000 Filter Set
Ex:FF01-438/24
DM:F482-Di01
Em:FF01-538/40
Lamp House
We use 150W Xenon Lamp House. It is very strong and miniSOG can be oxidized with weaker lamp. It is a good idea to try photo-oxidation with your existing lamp house system. Just avoid UV excitation, which will cause DAB to precipitate.
490nm LED source may be good for miniSOG since it can excite miniSOG well. 1000mW 488 nm is very strong and should be enough or need to attenuate depend on how big illumination area is.
Objective Lens
Our microscope has three objectives:
63x Oil 1.30
63x Water 1.15
20x multi immersion 0.7
Steps
Plate cells in MaTek dishes.
Fix in 2.5% glutaraldehyde in 0.1 M cacodylate buffer at room temperature for 5 min. Then, for one hour on ice.
**IMPORTANT: Keep Everything cold!**
Wash 5x for 1 min in 0.1M cacodylate buffer.
Block for 30 min on ice with blocking buffer.
Wash 3x in 0.1M cacodylate buffer for 1 min.
Block in 5 – 10 mM mersalyl acid for 30 min.
Wash 3x for 1 min with 0.1M cacodylate buffer.
Remove solution from plate and replace with DAB solution.
Microscope
At the microscope, set the temperature of the stage at 4˚C. Set the MaTek dish on the proper holder. Install oxygen, find target area with 63X objective lens, take initial picture (fluorescence + DIC).
Turn oxygen ON to blow onto surface of sample solution. (Regarding oxygenation: periodically replacing with freshly oxygenated solution is fine too when working with cultured cells).
Illuminate target area to photo-oxidize until light browning. Important: miniSOG is fast (2 to 10 minutes depending on protein). Optimal timing needs to be determined by investigator and will require the EM analysis of the samples at different reaction time.
Take final picture after photo-oxidation. Go to next area in the same dish and repeat, usually 3-4 areas per plate, making sure they are equally spaced to facilitate separation and cutting of individual blocks after polymerization.
When done, remove dish from holder, wash immediately 5x for 1 min in 0.1 M cacodylate buffer, on ice.
Fix in 1% osmium tetroxide in 0.1M cacodylate buffer. Leave 30 min on ice.
Wash 5x for 1 min in ddH2O.
Optional step: Add filtered 2% UA (uranyl acetate) in ddH2O at 4˚C for 1hr on ice. Wash 5x for 1 min in ddH2O.
Dehydrate: 20-50-70-90-100-100% cold Ethanol (1 min each). Then 100% dry ethanol at room temperature 3x for 1 minute.
Infiltration and Embedding: Prepare Durcupan: A:B:C:D=11.4:10:0.3:0.1 g
Add 50% ethanol: 50% Durcupan to dish. Leave for 30 min.
Pour out and add 100% Durcupan. Leave for 1 hour.
Add new 100% Durcupan resin, leave for 1 hr. Scrape out with a pair of plain wood applicators (Product No. 23-400-102 Fisherbrand) and without touching the cover slip containing the cells.
Add new 100% Durcupan resin, leave for 1 hr. Scrape out with a pair of plain wood applicators (Product No. 23-400-102 Fisherbrand) and without touching the cover slip containing the cells.
Add new 100% Durcupan resin, leave for 1 hr. Scrape out with a pair of plain wood applicators (Product No. 23-400-102 Fisherbrand) and without touching the cover slip containing the cells.
Add new 100% Durcupan resin, place in vacuum oven to polymerize for 48 hrs (60˚C).
